Aube Technologies TH113 AF, homeappliance

Download!

! " #$ FOR A AND AF MODELS ONLY At the rear of the control module are two potentiometers. Turn the dial to the desired temperature. Thank you for choosing Aube's non programmable thermostat. Your new electronic thermostat is equipped with a microprocessor and proportional integral adaptive (PIA) temperature control technology for total comfort. Depending on At the rear of the control module is a switch that has been factory-set to the applicable temperature control. NOTE: The AF model can be used for all temperature control types (A, F and AF). Note: The ambient These potentiometers act like a temperature lock. Even when occupants adjust the temperature using the dial on the front/rear of the control module, the potentiometers override the dial and maintain the temperature within the locked-in minimum and maximum range. A - ambient temperature TH113: The dial is located on the front of the control module. TH116: The dial is located on the rear of the control module. The min. position indicates the minimum temperature setpoint: 45°F (7°C). the selected model, this thermostat has been designed to control: A: The Ambient temperature (using an electric heating system) AF: The Ambient temperature with Floor temperature limit (using a floor heating system to heat the room) F: The Floor temperature (floor heating) NOTE: This control module must be mounted on a PB112 Series power base. The thermostat has an On/Standby switch making it possible to put the thermostat in sleep mode when its use is no longer required (e.g. summer). TH116 Public Area TH113 sensor is not operational when the switch is set to I (up). F & AF - floor temperature limit Use a flat tip screwdriver to rotate the potentiometers until the notch points to the desired temperature. Potentiometers Notch Temperature dial TH113 TH116 & ' Align the bracket tabs on the control module with the &' ( ' The GFCI monitors the electrical % " AUBE TECHNOLOGIES INC. ONE (1) YEAR LIMITED WARRANTY holes located on the power base. Follow the same procedure for the TH116. Control module flow for any loss of current; if there is any loss, the thermostat will cut off power to the heating system. We recommend you test the GFCI immediately after installing the control module, and once a month thereafter to ensure it is operating properly. To test: 🖉 Press the TEST button: • Successful: TEST warn The TH113 and TH116 are equipped with a remote input which allows connection of an optional telephone controller (CT240) or any other remote control system. When a command signal is received through this input, the thermostat automatically lowers its setpoint by 3.5°C. The LED lights up to indicate the signal's presence (except for GA and GB models). Bypass (not available for GA and GB power base): The TEST button can be used to bypass the signal for a 2-hour period. The LED goes off to indicate the bypass. NOTE: When combined with a GA/GB power base, the This product is guaranteed against workmanship defects for a one year period following the initial date of purchase. During this period, AUBE Technologies Inc. will repair or replace, at our option and without charge, any defective product which has been used under normal conditions. The warranty does not cover delivery costs and does not apply to products poorly installed or randomly damaged following installation. This warranty cancels and replaces any other manufacturer's express or implied warranty as well as any other company commitment. AUBE Technologies Inc. cannot be held liable for related or random damages following the installation of this product. The defective product as well as the purchase invoice must be returned to the place of purchase or mailed, prepaid and insured, to the following address: Aube Technologies Inc. 705 Montrichard Saint-Jean-sur-Richelieu, Quebec, Canada J2X 5K8 Power base NOTE: Keep the thermostat's air vents clean and free from obstructions. NOTE: The screw cannot be removed completely. ing light is ON and power to heating system is cut off. • Unsucessful: The TEST warning light is OFF. Cut power to heating system from the main power panel and call customer service. ✂ When successful, reset thermostat (STANDBY/ON) to power heating system. NOTE: If the test warning light comes ON during normal operation, cut power to heating system from the main power panel and have an electrician verify the installation. TEST button is used only for GFCI testing. The bypass function is not available with these power base models. $ Models: TH113 and TH116 A / AF / F Setting range: 45°F, 59°F to 95°F (7°C, 15°C to 35°C) Potentiometers: minimum: 41°F to 77°F (5°C to 25°C) maximum: 59°F to 95°F (15°C to 35°C) Accuracy: ± 0.9°F (0.5°C) Storage: -4°F to 120°F (-20°C to 50°C) If you have any questions concerning the TH113 or the TH116 thermostat, call our technical support team at: Phone: Montreal area: (450) 358-4600 Canada / U.S.: 1-800-831-AUBE (2823) Fax: y(450) 358-4650 Email: service@aubetech.com Monday to Friday from 8:30 AM to 5:00 PM EST. For more information on our products, visit us at: www.aubetech.com 01/08/03 920-113-001-00-1-A Installation Instructions 1. Introduction 3.2 Slave Units - Installation and Wiring MASTER THERMOSTATS TH113-A/F/AF (12VDC) TH114-A/F/AF (12VDC) TH115-A/F/AF (12VDC) TH116-A/F/AF (12VDC) SLAVE UNITS CT230-120GA CT230-120GB CT230-240GA CT230-240GB This master and slave unit system is specially designed for large floor heating applications exceeding 15 A. The master thermostat controls a single or multiple floor heating zones driven by slave units. The master thermostat can control up to 10 slave units. Each slave unit drives its own zone and is equipped with a GFCI test button and warning light as well as an On/Standby switch to facilitate maintenance on specific zones of the floor installation. 2. Operation Master Thermostat The master unit controls the temperature and sends a signal to slave units when heating is required. The floor sensor is connected to the master unit. The master unit is powered by the slave units. Slave Unit The slave unit receives the signal sent by the master unit and activates its load. NOTE: There must be a minimum of one slave unit ON to power the master unit. 3. Installation Turn off power to the heating system at the main power panel to avoid electrical shock. Installation should be carried out by an electrician. 3.1 Wiring Guidelines • The wire distance between the master thermo stat and slave unit should not exceed 500 ft. (150 m). • The floor sensor cable should not exceed 200 ft. (60 m). • A 3-wire 20 AWG cable is recommended. FIGURE 1 Connections The slave units can operate on different voltages (e.g. 5 units @ 120 V and 5 @ 240 V). • Required parts: CT230-120GA, -120GB, -240GA or -240GB • Installation: On an electrical box • Location: Installation near the master thermostat is not required (i.e. can be installed in a utility room). • Wiring: The power bases are joined through a daisy chain connection. ■ Connect the 120 V or 240 V power base wires to the power (line) and to the load (floor) using solderless con nectors for copper wires, and secure the base to the electrical box. □ Affix the wiring sticker (in the CT230 box) to the base. 🞐 Connect the slave power bases together as per FIGURE 1. ❑ Once installation and wiring is com plete, mount the CT230 interface: a) Align the bracket tabs of the CT230 with the holes located on top of the power base. b) Secure the CT230 interface using the screw (captive). ❒ Switch all slave power bases to STANDBY by sliding the protective door upwards and positioning the switch to STANDBY. Install and connect the master unit (see 3.3). 400-230-000-C 5/12/05 1/2 3.3 Master Thermostat - Installation and Wiring WARNING: Make sure all slave units are in STANDBY mode. •Required parts: TH113-A/F/AF (12VDC), TH114-A/F/AF (12VDC), TH115-A/F/AF (12VDC) or TH116-A/F/AF (12VDC) • Location: anywhere easily accessible to users. Technical Specifications Temperature: - Operation: 32°F to 122°F (0°C to 50°C) - Storage: -4°F to 122°F (-20°C to 50°C) TH113/TH114/TH115/TH116 (A/F/AF-12VDC) Power supply 12 V from remote unit Temperature control: AF (ambient with floor limit) / A (ambient) • Install the master thermostat in the controlled area. Maximum slave units up to 10 slave units per master thermostat • Choose a location about 5 ft. above the floor in an area where the tempera Wire gauge 20 AWG ture is stable. • Avoid locations where there are air drafts (top of staircase, air outlet), dead air spots (behind a door), direct sunlight or concealed chimneys or stove pipes. Size (H • W • D) BASE 4.63 x 2.7 x 0.61 in. (117.5 x 68.3 x 15 mm) Temperature control: F (floor) • Can be installed anywhere. ⬧ Wire the 12 VDC base to the nearest slave unit. The floor sensor must be installed in an area where average temperature can be NOTE: Refer to the TH11x user guide for techni cal specifications. CT230-120GA/120GB/240GA/240GB Supply read. The cable must follow the wall down to the floor and must not cross any heater wires or be directly on or adjacent to a heating wire. For maximum performance, the sensor probe should be centered between the wires in the mat (max. 80°C). - PB112-120 - PB112-240 1800 W @ 120 VAC 60 Hz, 15 A resistive 3600 W @ 240 VAC 60 Hz, 15 A resistive ⧫ Push the excess wire into the wall, secure the base using the provided screws and wall anchors, and install the TH11x thermostat onto the base. ◆ Once the thermostat is installed, return power to heating system and switch all GFCI GA=5 mA / GB=30 mA Certification c CSA us slave units and the master thermostat to ON. Size (H • W • D) BASE Size (H • W • D) INTERFACE Service 4.63 x 2.7 x 1.45 in. (117.5 x 68.3 x 37 mm) 4.67 x 2.74 x 0.67 in. (118.6 x 69.6 x 17 mm) 3.4 Slave Units - GFCI Test We recommend you test the GFCI immediately after installing the thermostat, and once a month thereafter to ensure it is operating properly. If the test warning light comes ON during normal operation, cut power to heating system from the main power panel and verify the installation. ■ Slide the protective door upwards and make sure the switch is ON. □ Press TEST. • The test is successful if the TEST warning light is ON and power is cut off. • If the test fails (first installation test): a. Verify installation b. Check the load wires c. Once you've identified the problem, run the GFCI test again • If the test fails (monthly maintenance): a. Cut power to heating system from the main power panel and call customer service 🞐 When the test is successful, reset the slave unit by switching from ON to STANDBY then back to ON. ❑ Repeat steps 1 to 3 for all slave units. If you have any questions concerning the installation of the master thermostat or slave units, contact our technical support team at: Montreal area: (450) 358-4600 Canada / U.S.: 1-800-831-AUBE (2823) Fax: (450) 358-4650 Email: service@aubetech.com Monday to Friday from 8:30 AM to 5:00 PM EST. For more information on our products, visit us at www.aubetech.com Warranty AUBE TECHNOLOGIES INC. ONE (1) YEAR LIMITED WARRANTY This product is guaranteed against workmanship defects for a one year period following the initial date of purchase. During this period, AUBE Technologies Inc. will repair or replace, at our option and without charge, any defective product which has been used under normal conditions. The warranty does not cover delivery costs and does not apply to products poorly installed or randomly damaged following installation. This warranty cancels and replaces any other manufacturer's express or implied warranty as well as any other company commitment. AUBE Technologies Inc. cannot be held liable for related or random damages following the installation of this product. The defective product as well as the purchase invoice must be returned to the place of purchase or mailed, prepaid and insured, to the following address: Aube Technologies Inc. 705 Montrichard Saint-Jean-sur-Richelieu, Quebec, Canada J2X 5K8 400-230-000-C 5/12/05 2/2