Billy Goat KD Vacuum KD611, homeappliance

Download!

KD Owner's Manual BILLY GOAT KD VACUUM Owner's Manual KD612, KD512HC, KD512HCS Accessories Optional Debris bags SHREDDER KIT Shreds leaves, reducing total volume. P/N 890209 ON BOARD VACUUM HOSE KIT 4"(102mm) x 7' (2.13m) For vacuuming in hard to reach areas. P/N 890041 NOZZLE WEAR PLATES (STD. ON KD512HCS) Extends nozzle life when used along curbs and hard surfaces. P/N 890413 CASTER KIT For use on hard surface. P/N 890412 STANDARD TURF PRO DEBRIS BAG For use in leaves and grass in non dusty conditions. P/N 890028 DEBRIS BAG COVER Directs dust downward away from operator. P/N 900801 ZIPPERLESS QUICK BAG For non-dusty conditions that are damaging to zippers. P/N 890309 Part No 890033 Form No F062306A 1 KD Owner's Manual ABOUT THIS MANUAL THANK YOU for purchasing a BILLY GOAT®KD Vacuum. Your new machine has been carefully designed and manufactured to provide years of reliable and productive service. This manual provides complete operating and maintenance instructions that will help to maintain your machine in top running order. Read this manual carefully before assembling, operating, or servicing your equipment. CONTENTS SERIAL PLATE DATA AND SPECIFICATIONS 3 GENERAL SAFETY 4-5 SOUND AND VIBRATION 6 INSTRUCTION LABELS 7 PACKING CHECKLIST & ASSEMBLY 8 OPERATION 9-10 MAINTENANCE 11 TROUBLESHOOTING AND WARRANTY PROCEDURE 12 MAINTENANCE RECORD 13 ILLUSTRATED PARTS & PARTS LISTS 14-15 Part No 890033 Form No F062306A 2 KD Owner's Manual SERIAL PLATE DATA Record the model number, serial number, date of purchase, and where purchased. Purchase Date: Purchased From: Specifications KD612 KD512HC KD512HCS Engine: HP 6.0 (4.47 kW) 5.5 (4.11 kW) 5.5 (4.11 kW) Engine: Type B & S QUANTUM HONDA OHC HONDA OHC Engine: Model 112K020124E1 GCV160AN1A GCV160AN1A Engine: Fuel Capacity 1.5 qt. (1.4 L) 1.16 qt. (1.1 L) 1.16 qt. (1.1 L) Engine: Oil Capacity 0.63 qt. (0.6 L) 0.58 qt. (0.6 L) 0.58 qt. (0.6 L) Total Unit Weight: 98# (44.5 kg) 99# (45.0 kg) 99# (45.0 kg) Overall Length 62" (1.57m) 62" (1.57m) 62" (1.57m) Overall Width 26.75" (0.68 m) 26.75" (0.68 m) 26.75" (0.68 m) Overall Height 42" (1.07m) 42" (1.07m) 42" (1.07m) Max. operating slope 200 200 200 Lwa at operator position 111 dBa 111 dBa 111 dBa Lpa at operator position 97 dBa 97dBa 97dBa Vibration at operator position 0.34 g (3.29m/s2) 0.27 g (2.86m/s2) 0.27 g (2.86m/s2) Part No 890033 Form No F062306A 3 KD Owner's Manual GENERAL SAFETY INSTRUCTIONS and SYMBOLS The safety symbols shown below are used throughout this manual. You should become familiar with them before assembling, operating, or servicing this equipment. This symbol indicates important information that will prevent injury to yourself or others. This symbol indicates ear protection is recommended when operating this equipment. This symbol indicates eye protection is recommended when operating this equipment. This symbol indicates gloves should be worn when servicing this equipment. This symbol indicates that this manual and the engine manufacturer's manual should be read carefully before assembling, operation, or servicing this equipment. This symbol indicates important information that will prevent damage to your BILLY GOAT® KD Vacuum. This symbol indicates the engine oil level should be checked before operating this equipment. Read and make sure you thoroughly understand the following safety precautions before assembling, operating or servicing this equipment: READ this manual and the engine manufacturer's manual carefully before assembling, operating, or servicing this equipment. EAR PROTECTION is recommended when operating this equipment. EYE PROTECTION is recommended when operating this equipment. BREATHING PROTECTION is recommended when operating this equipment. EXHAUST from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. DO NOT operate this equipment on any unimproved forested, brushy, or grass covered land unless a spark arrester is installed on the muffler as required by Section 4442 of the California Public Resources Code. The arrester must be maintained in good working order. Other states may have similar laws. Federal laws apply on federal lands. DO NOT run engine in an enclosed area. Exhaust gases contain carbon monoxide, an odorless and possibly fatal poison. Part No 890033 Form No F062306A 4 KD Owner's Manual DO NOT run this equipment indoors or in any poorly ventilated area. Refueling outdoors is recommended. DO NOT refuel this equipment while the engine is running. Allow engine to cool for at least two minutes before refueling. DO NOT store gasoline near an open flame. DO NOT remove gas cap while engine is running. DO NOT start or operate engine if strong odor of gasoline is present. DO NOT start or operate engine if gasoline is spilled. Move equipment away from spill until gasoline has completely evaporated. DO NOT smoke while filling the fuel tank. DO NOT check for spark with spark plug or spark plug wire removed. Use an approved spark tester. DO NOT operate engine without a muffler. Inspect muffler periodically and replace if necessary. If equipped with muffler deflector, inspect deflector periodically and replace if necessary. DO NOT operate engine with grass, leaves or other combustible material near the muffler. DO NOT touch muffler, cylinder, or cooling fins when hot. Contact with hot surfaces may cause severe burns. DO NOT leave equipment unattended while in operation. DO NOT park equipment on a steep grade or slope. DO NOT operate equipment with bystanders in or near the work area. DO NOT allow children to operate this equipment. DO NOT operate equipment with guards removed. DO NOT operate equipment near hot or burning debris or any toxic or explosive materials. DO NOT operate equipment on slopes greater than specified in Specifications section of this manual. DO NOT place hands or feet underneath unit, or near any moving parts. ALWAYS remove spark plug wire when servicing equipment to prevent accidental starting. ALWAYS check fuel lines and fittings frequently for cracks or leaks. Replace if necessary. ALWAYS keep hands and feet away from moving or rotating parts. ALWAYS store fuel in approved safety containers. WARNING: Important Remove all rocks, wire, string, plastic, etc. that can present a hazard during work prior to starting. DO identify and mark all fixed objects to be avoided during work such as sprinkler heads, water valves, buried cables, or clothes line anchors, etc. Part No 890033 Form No F062306A 5 KD Owner's Manual SOUND SOUND LEVEL 97 dB(a) at Operator Position Sound tests were conducted in accordance with 2000/14/EEC, and were performed on 2-21-2002 under the conditions listed below. Sound power level listed is the highest value for any model covered in this manual. Please refer to serial plate on the unit for the sound power level for your model. General Conditions: Sunny Temperature: 45oF (7.2oC) Wind Speed: 5 mph (8.1 kmh) Wind Direction: South West Humidity: 60% Barometric Pressure: 30.18"Hg (767 mm Hg) VIBRATION DATA VIBRATION LEVEL 0.34g (3.29m/s2) Vibration levels at the operator's handles were measured in the vertical, lateral and longitudinal directions using calibrated vibration test equipment. Tests were performed on 5-25-2006 under the conditions listed below. General Conditions: Sunny Temperature: 89oF (31.7oC) Wind Speed: 13.6 mph (21.9kph) Wind Direction: East Humidity: 22.8% Barometric Pressure: 29.9Hg (101.3kpa) INTENDED USE INTENDED USE: This machine is designed for vacuuming leaves, grass clippings and other types of organic litter and for chipping brush, limbs, corn and sunflower stalks and palm fronds. Debris mixed with cans, bottles and small amounts of sand can be vacuumed; however, it is not this machine's primary purpose. Vacuuming cans, bottles and sand will affect the longevity of your machine. Do not operate if excessive vibration occurs. If excessive vibration occurs, shut engine off immediately and check for damaged or worn impeller, loose impeller bolt, loose impeller key, loose engine or lodged foreign objects. Note: See parts list for proper impeller bolt torque specifications. (See trouble shooting section on page 12). Part No 890033 Form No F062306A 6 KD Owner's Manual INSTRUCTION LABELS The labels shown below were installed on your BILLY GOAT® KD Vacuum. If any labels are damaged or missing, replace them before operating this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for convenience in ordering replacement labels. The correct position for each label may be determined by referring to the Figure and Item numbers shown. LABEL DANGER KEEP HANDS LABEL EAR EYE BREATHING ITEM #49 DANGER FLYING DEBRIS AND FEET AWAY P/N 890254 ITEM # 62 P/N 810736 ITEM #29 P/N 400424 LABEL READ MANUAL LABEL EXPLOSIVE FUEL DEBRIS BAG LABEL ITEM #84 P/N 430363 ITEM # 63 P/N 400268 ITEM #1 ENGINE LABELS HONDA BRIGGS & STRATTON Read Owner's Manual Before Operating. Lire le manuel d'utilisation avant la mise en route. Vor Inbetriebnahme Bedienungs - und Wartungsanleitung lesen. Favor leer las instrucciones de operacion antes de operar el motor. Consultare il Manuale Uso e Manutenzione prima dell utilizzo. Las Skotselinstruktionen Innan Start. ENGINE CONTROLS Honda Choke Throttle Control Control Choke Control Throttle Control Fuel Shut Off Briggs engines have a primer button carburetor rather than choke type carburetor. Part No 890033 Form No F062306A 7 KD Owner's Manual PACKING CHECKLIST Your Billy Goat KD Vacuum is shipped from the factory in one carton, completely assembled except for the upper handle, debris bag, and bag quick disconnect. READ all safety instructions before assembling unit. TAKE CAUTION when removing the unit from the box the Handle Assembly is attached by cables and folded over PUT OIL IN ENGINE BEFORE STARTING PARTS BAG & LITERATURE ASSY Warranty card P/N- 400972, Owner's Manual P/N-890033, Declaration of Conformity P/N-890393. Boxing Parts Checklist Debris Bag P/N-890022 Literature Assy P/N-890392 Connector Quick Disconnect P/N-890176 Quick disconnect Fig. 2 ASSEMBLY Honda 5.5GVC 160 Briggs & Stratton 6.0 HP Intek 1. ASSEMBLE Lift upper handle (item 6), remove items 8, 30, & 32 from lower handle (item 27). Attach and secure upper handle as shown using same hardware. 2. UNFOLD the debris bag (item 1) and fasten bag neck to bag quick disconnect (item 64). Attach firmly to housing exhaust (item 52) see fig. 2. 3. ATTACH bag hanger strap to bag supports (item 11), preassembled to upper handle. 4. CONNECT spark plug wire. Part No 890033 Form No F062306A 8 KD Owner's Manual OPERATION Like all mechanical tools, reasonable care must be used when operating machine. Inspect machine work area and machine before operating. Make sure that all operators of this equipment are trained in general machine use and safety. PUT OIL IN ENGINE BEFORE STARTING STARTING ENGINE: See engine manufacturer's instructions for type and amount of oil and gasoline used. Engine must be level when checking and filling oil and gasoline. ENGINE SPEED: Controlled by throttle lever on the engine. Under normal conditions, operate at minimum throttle to accomplish your current cleaning task. FUEL VALVE: Move fuel valve to "ON" position (when provided on engine). CHOKE: Located on engine and must be controlled manually. PRIMER: Push primer per engine instructions (B&S only). THROTTLE: Located on engine and must be controlled manually. IF YOUR UNIT FAILS TO START: See Troubleshooting on page 12. HANDLING & TRANSPORTING: This unit requires two people to lift it. With the handle in the folded position, lift holding the lower handle and belt/shaft guard one on each side of the machine. Secure the machine in place during transport. See page 3 for weight specifications Never lift the machine while the engine is running. STORAGE Never store engine indoors or in enclosed poorly ventilated areas with fuel in tank, where fuel fumes may reach an open flame, spark or pilot light, as on a furnace, water heater, clothes dryer or other gas appliance. If engine is to be unused for 30 days or more, prepare as follows: Remove all gasoline from carburetor and fuel tank to prevent gum deposits from forming on these parts and causing possible malfunction of engine. Drain fuel outdoors, into an approved container, away from open flame. Be sure engine is cool. Do not smoke. Run engine until fuel tank is empty and engine runs out of gasoline. Part No 890033 Form No F062306A 9 KD Owner's Manual OPERATION VACUUMING OPERATION VACUUM NOZZLE HEIGHT ADJUSTMENT: is raised and lowered by pulling slightly upward on handle and pulling height adjust knob on the handle (item 23) up at left rear of machine. FOR MAXIMUM PICKUP: Adjust nozzle close to debris, but without blocking airflow into the nozzle. NOTE: Never bury nozzle into debris. CLEARING A CLOGGED NOZZLE & EXHAUST: Turn engine off and wait for impeller to stop completely and disconnect spark plug wire. Wearing durable gloves, remove clog. Danger, the clog may contain sharp materials. Reconnect spark plug wire. DEBRIS BAG Debris bags are normal replaceable wear items. Note: Frequently empty debris to prevent bag overloading with more weight than you can lift. An optional bag and dust cover is available for use where debris will be vacuumed in dusty conditions (see Optional Accessories shown on page 1). DO NOT place bag on or near hot surface, such as engine. Run engine at 1/2 throttle for first 1/2 hour to condition new bag. Your new bag requires a break-in period to condition the pores of the material against premature blockage. The entire bag surface serves as a filter, and must be able to breath to have good vacuum performance. Be sure engine has come to a complete stop before removing or emptying bag. This vacuum is designed for picking up trash, organic material and other similar debris (see Safety Warnings page 4-5). However, many vacuums are used where dust is mixed with trash. Your unit can intermittently vacuum in dusty areas. Dust is the greatest cause of lost vacuum performance. However, following these rules will help maintain your machine's ability to vacuum in dusty conditions: • Run machine at idle to quarter throttle. • The debris bag must be cleaned more frequently. A vacuum with a clean, pillow soft bag will have good pickup performance. One with a dirty, tight bag will have poor pickup performance. If dirty, empty debris and vigorously shake bag free of dust. • Pressure-wash debris bag if normal cleaning does not fully clean bag. Bag should be thoroughly dry before use. NOTE: Having one or more spare debris bags is a good way to reduce down time while dirty bags are being cleaned. DO NOT leave debris in bag while in storage. COMPOST Vacuumed leaves, grass and other organic material from your own yard can be emptied into a pile or composter to provide enriched soil for later use as fertilizer in gardens and flower beds NOTE: Allow green chips to dry before spreading around living plants. Part No 890033 Form No F062306A 10 KD Owner's Manual MAINTENANCE PERIODIC MAINTENANCE Periodic maintenance should be performed at the following intervals: Maintenance Operation Every Use (daily) Every 5 hrs (daily) Every 25 Hours Inspect for loose, worn or damaged parts. Clean Debris bag Check bag strap tightness Engine (See Engine Manual) Check for excessive vibration Lubricate wheels IMPELLER REMOVAL 1.Wait for engine to cool and disconnect spark plug. 2.Drain fuel and oil from the engine. 3. Remove bag, quick release, and upper handle. Do not kink, stretch, or break control cables, control housings, or end fittings while removing handles. 4. Remove housing top plate by removing bolts around outside of housing. 5. Leaving engine fastened to top plate, turn it upside down so the impeller is on top. 6. Remove impeller bolt and lock washer. 7. Lift impeller upward. If impeller slides freely, proceed to (step 10). 8. Place two crowbars between impeller and housing on opposite sides. Pry impeller away from engine until it loosens. Using a penetrating oil can help loosen a stuck impeller. 9. If the impeller does not loosen, obtain a 1" (25.4mm) longer bolt of the same diameter and thread type as the impeller bolt. Thread longer bolt by hand into the crankshaft until bolt bottoms. Using a suitable gear or wheel puller against the bolt head and the impeller back-plate (near the blades), remove impeller from shaft. 10. Using a new impeller bolt and lockwasher, reinstall new impeller in reverse order. 11. Tighten impeller bolt. Torque impeller bolt to 50 Ft. Lbs. (68 N.m) (see item 51 on page 15). 12. Reinstall engine onto housing in reverse order of removal. 13. Gas and oil (0.69 quart). 14. Reinstall spark plug wire. Part No 890033 Form No F062306A 11 KD Owner's Manual Troubleshooting Problem Possible C ause Solution Abnorm al vibration. · Loose or out of balance im peller or loose engine · C hec k im peller and replace if required. C hec k engine W ill not vacuum or has poor vacuum perform ance · dirty debris bag. N ozzle height set too high or low . H ose k it cap m issing. C logged nozzle or exhaus t. Excessive quantity of debris. · C lean debris bag. Shake bag c lean or w ash. Adjus t nozzle height. C heck for hose k it cap. U nclog nozzle or exhaust. Allow air to feed w ith debris Engine w ill not start. · Stop sw itch off. T hrottle in off position. Engine not in full choke pos ition. O ut of gasoline. Bad or old gasoline. Sparkplug w ire disconnected. D irty air cleaner · C hec k stop sw itches, throttle, choke pos ition and gasoline. C onnect spark plug w ire. C lean or replace air filter. O r contact a qualified service person. Engine is locked, w ill not pull over. · D ebris loc ked in im peller. Engine problem . · See page 5. C ontac t a engine service dealer for engine problem s N ozzle s crapes ground in low es t height setting. N ozzle height out of adjustm ent Adjus t nozzle height (See N ozzle height fine adjustm ent for hard surfaces on page 5 When servicing engine refer to specific manufacturers engine owner's manual. Engine warranty is covered by the specific engine manufacturer. If your engine requires warranty or other repair work contact your local servicing engine dealer. When contacting a dealer for service it is a good idea to have your engine model number available for reference (See table page 3). If you cannot locate a servicing dealer in your area you can contact the manufacturers national service organization. To reach: American Honda: 800-426-7701 WARRANTY CLAIM PROCEDURE Should a BILLY GOAT® machine fail due to a defect in material and/or workmanship, the owner should make a warranty claim as follows: • The machine must be taken to the dealer from whom it was purchased or to an authorized Servicing BILLY GOAT Dealer. • The owner must present the remaining half of the Warranty Registration Card, or, if this is not available, the invoice or receipt. • The Warranty Claim will be completed by the authorized BILLY GOAT Dealer and submitted to their respective BILLY GOAT Distributor for their territory Attention: Service Manager. Any parts replaced under warranty must be tagged and retained for 90 days. The model number and serial number of the unit must be stated in the Warranty Claim. • The distributor service manager will sign off on the claim and submit it to BILLY GOAT for consideration. • The Technical Service Department at BILLY GOAT will study the claim and may request parts to be returned for examination. BILLY GOAT will notify their conclusions to the distributor service manager from whom the claim was received. • The decision by the Technical Service Department at BILLY GOAT to approve or reject a Warranty Claim is final and binding. For online product registration go to www.billygoat.com Part No 890033 Form No F062306A 12 KD Owner's Manual MAINTENANCE RECORD Date Service Performed Part No 890033 Form No F062306A 13 KD Owner's Manual PARTS DRAWING KD Part No 890033 Form No F062306A 14 * Denotes standard hardware item that may be purchase d locally. KD Owner's Manual PARTS LIST ITE M N O . D ES C R IPTIO N K D 612 Part N o. Q TY K D 512H C Part N o. Q TY K D 512H C S Part N o. Q TY 1 P R O D EB R IS BA G (serv ice) 890305 1 890023 1 890023 1 2 3 4 5 6 N U T LO C K (1/4 - 20 ) S C R E W C AP ( 1/4 - 20 x 1-1/2 H EX ) H A N D LE ASS'Y (inc l. item s 4(5),5(5),11(2),75(2),76) *8160001 *8041008 900054 7 8 1 *8160001 *8041008 900054 7 8 1 *8160001 *8041008 900054 7 8 1 7 AXLE H EIG H T A D JU ST 890389 1 890389 1 890389 1 8 S C R E W H A N D LE 5/16 - 18 x 1 - 3/4 *8041031 2 *8041031 2 *8041031 2 9 C LA M P C ABLE 900407 2 900407 2 900407 2 10 S C R E W C AP 1/4 - 20 x 1 3/4 *8041009 1 *8041009 1 *8041009 1 11 BA R BA G S U PP O R T 900039 2 900039 2 900039 2 12 D O O R EX H A U ST ASS'Y (incl. item 62 ) 890148 1 890148 1 890148 1 13 PLATE TO P ASS'Y (incl. item s 29, 57, 65) 890402 1 890402 1 890402 1 14 B O LT-C A R R IA G E 1/4x3/4 *8024021 2 *8024021 2 *8024021 2 15 W AS H E R FLAT 5/16 8172008 1 8172008 1 8172008 1 16 W AS H E R 1/4 F C ZP *8171002 10 *8171002 10 *8171002 10 17 18 B R A C KET - H EIG H T A D JU ST M E N T 890021 1 890021 1 890021 1 19 PLATE U PPE R H EIG H T A D JU ST 890005 1 890005 1 890005 1 20 SP R IN G 900136 1 900136 1 900136 1 21 TIR E - O N LY (PE R ASSY) 900507 1 900507 1 900507 1 22 PIN - H AIR C O TTE R 900471 1 900471 1 900471 1 23 C ABLE H EIG H T A D JU ST M E N T 890019 1 890019 1 890019 1 24 B O LT - C A R R IA G E 5/16 - 18 x 4 1/2 *8024054 4 *8024054 4 *8024054 4 25 26 N U T LO C K 5/16 - 18 H EX *8160002 6 *8160002 6 *8160002 6 27 H A N D LE LO W E R K D 510 890346 1 890346 1 890346 1 28 PLATE H A N D LE S U PP O R T 900933 1 -2 900933 1 -2 900933 1 -2 29 LABEL D A N G E R C U T FIN G E R 400424 2 400424 2 400424 2 30 W AS H E R FLAT C U T 5/16 *8171003 2 *8171003 2 *8171003 6 31 32 N U T LO C K 5/16 - 18 T H IN H T. *8161041 4 33 G R IP H A N D LE 400570 2 400570 2 34 W H EEL ASS'Y (inc l. item s 21) 900509 4 900509 4 900509 4 35 W AS H E R 0.75 "C " 900997 0 -1 900997 0 -1 900997 0 -1 36 37 S C R E W S M 1/4x3/4 TYPE A - - - - *8122082 4 38 PLATE SKID (inc l. item s 54) - - - - 890413 1 39 SPA C E R IM PELLE R - - 890616 1 890616 1 40 41 42 S C R E W SELF TAPPIN G 10 - 24 x 1/2 *8123086 1 *8123086 1 *8123086 1 43 N O ZZLE M AIN FR A M E ASS'Y (inc l. one of item s 29,44,42) 890391 1 890391 1 890391 1 44 PLU G 900146 1 900146 1 900146 1 45 LIN E R H O LD PLATE 890618 2 890618 2 890618 2 46 - - - - 47 IM PELLE R ASS'Y (incl. item s 49, 50, 51 ) 900215 1 890615 1 890615 1 48 49 KEY 900162 2 900162 2 900162 2 50 W AS H E R LO C K 3/8 TW ISTE D TO O T H 400502 1 400502 1 400502 1 51 S C R E W C AP 3/8 -24 x 1 G R 8 (TO R Q .50 FT-LBS)(68N .m ) 900154 1 900154 1 900154 1 52 H O U SIN G ASS'Y (inc l. item s 12, 14, 15, 16, 66) 890371-S 1 890371-S 1 890417-S 1 53 54 E N G IN E H O N D A 5.5 H .P. G C 160 - - 890614 1 890614 1 E N G IN E B R IG G S & ST R ATTO N 6 H .P. Q U A N TU M IC 890622 1 - - - - B O LT C A R R IA G E 5/16-18x3/4" - - - - 8024039 4 55 LIN E PV C - - - - 900732-S 1 56 S C R E W C AP 3/8 - 1-1/2 TAPTITE 890408 4 890408 4 890408 4 57 58 S C R E W C AP 1/4 - 20 x 1/2 H W H 890359 15 890359 15 890359 15 W AS H E R FLAT 1/2 SAE *8172011 8 *8172011 8 *8172011 8 59 S C R E W S O C KET H D . 5/16 - 18 x 3/4 G R . 8 60 H G T A D JU ST ASSY (IN C L. ITE M S 18, 20, 22, 23) 890013 1 890013 1 890013 1 61 1/2-13 C AP N U T N P W /PAT C H 890530 4 890530 4 890530 4 62 LABEL D A N G E R FLYIN G M ATE R IAL 810736 1 810736 1 810736 1 63 LABEL D O N O T FILL W H E N E N G IN E IS H O T 400268 1 400268 1 400268 1 64 C O N N E C TO R BA G Q U IC K 890176 1 890176 1 890176 1 65 LABEL R EA D O W N E R 'S M A N U AL 890301 1 890301 1 890301 1 66 LABEL EA R /EYE B R EATH IN G 890254 1 890254 1 890254 1 Part No 890033 Form No F062306A 15 KD Owner's Manual BRUSH CUTTER FORCE BLOWER AERATOR If you liked this product please feel free to view our full line of quality lawn care, renovation, and debris removal products at www.billygoat.com QL VACUUM MULTI VACUUM POWER RAKE Part No 890033 Form No F062306A 16