Annovi Reverberi Power-jet Cleaner 810, homeappliance

Download!

820 - 830 S I A Ç N A R F H S I L G N E H C S T U E D O N A I L A T I L O Ñ A P S E Й И К С С У Р cod. 90662 - FZ FR Lire ce manuel avant l'installation/utilisation du nettoyeur en faisant très attention aux INSTRUCTIONS POUR LA SÉCURITÉ EN Read this manual through carefully before installing/using the cleaner, paying special attention to the SAFETY INSTRUCTIONS DE Lesen Sie dieses Handbuch vor der Installation und dem Gebrauch des Hochdruckreinigers aufmerksam durch und achten Sie besonders auf die SICHERHEITSANWEISUNGEN IT Leggere questo manuale prima dell'installazione/uso dell'idropulitrice, prestando particolare attenzione alle ISTRUZIONI PER LA SICUREZZA ES Leer este manual antes de la instalación/uso de la hidrolimpiadora, prestando particular atención a las INSTRUCCIONES SOBRE SEGURIDAD RU Прочитайте данное руководство перед установкой моечной машины, обращая особенное внимание на ИНСТРУКЦИИ ПО БЕЗОПАСНОСТИ DÉCLARATION DE CONFORMITÉ FR Nous déclarons, en assumant la pleine responsabilité de cette déclaration, que le produit est conforme aux normes suivantes et aux documents correspondants EN 60335-2-79:2004 Selon les prescriptions des directives : 98/37/CE 73/23/CEE, 89/336/CEE, 2000/14/CE Date: 24/03/2006 MODENA (I) Stefano Reverberi Managing Director DICHIARAZIONE DI CONFORMITÀ IT Dichiariamo, assumendo la piena responsabilità di tale dichiarazione, che il prodotto è conforme alle seguenti normative e ai relativi documenti EN 60335-2-79:2004 in base alle prescrizioni delle direttive: 98/37/CE CEE 73/23, CEE 89/336, 2000/14/CE Data: 24/03/2006 MODENA (I) Stefano Reverberi Managing Director DECLARATION OF CONFORMITY EN We declare under our sole responsibility that this product is in conformity with the following standards or standardized documents EN 60335-2-79:2004 In accordance with the regulations: 98/37/EC EEC 73/23, EEC 89/336, 2000/14/EC Date: 24/03/2006 MODENA (I) Stefano Reverberi Managing Director DECLARACIÓN DE CONFORMIDAD ES Declaramos, asumiéndonos la plena responsabilidad al respecto, que el producto cumple con lo establecido por las siguientes normativas y relativos documentos: EN 60335-2-79:2004 sobre la base de lo dispuesto por las directivas: 98/37/CE 73/23/CEE, 89/336/CEE y 2000/14/CE Fecha: 24/03/2006 MÓDENA (I) Stefano Reverberi Managing Director KONFORMITÄTSERKLÄRUNG DE Wir erklären in alleiniger Verantwortung, dass das Produkt den folgenden Normen und normativen Dokumenten entspricht: EN 60335-2-79:2004 gemäß den Bestimmungen der Richtlinien: 98/37/EG 73/23/EWG, 89/336/EWG, 2000/14/EG Datum: 24.03.2006 MODENA (I) Stefano Reverberi Managing Director ДЕКЛАРАЦИЯ СООТВЕТСТВИЯ RU Заявляем, возлагая на себя полную ответственность за данную декларацию, что данная продукция соответствует следующим нормам и соответствующим документам EN 60335-2-79:2004 на основании требований директив: 98/37/EC 73/23/EEC, 89/336/EEC, 2004/14/EC Дата: 24/03/2006 Модена (Италия) Стефано Ревербери Управляющий директор E1 E2 B1 A1 A2 A3 A4 C1 B6 A5 D1 B3 B7 C2 D B5 B4 1 1 4 5 2 6 3 Ø13 2 12 G E 3 1 23 D 1 I 2 4 L 5 10 10 English 1 GENERAL INFORMATION (FIG. 1) 1.1 Use of the manual The USE • MAINTENANCE manual forms an integral part of the power-jet cleaner and should be kept for future reference. Please read it carefully before installing/using the appli ance. Read the engine manufacturer's manual carefully. If the appliance is sold, the seller must pass on the manuals to the new owner along with the appliance. 1.2 Delivery The cleaner is delivered partially assembled in a card board box, fixed to a pallet. Caution - Danger! Suitable lifting equipment must be used when lifting the power-jet cleaner. The supply package is illustrated in fig.1 1.2.1 Documentation supplied with the appliance A1 Use and maintenance manual A2 Safety instructions A3 Declaration of conformity A4 Technical data A5 Engine instruction manual 1.3 Disposing of packaging The packaging material must be disposed of in accord ance with the relevant legal requirements. 1.4 Safety signs Comply with the instructions provided by the safety signs fitted to the cleaner. Check that they are present and legible; otherwise, fit replacements in the original positions. E1 sign - indicates that the cleaner must not be dis posed of as municipal waste; it may be handed in to the dealer on purchase of a new cleaner. The cleaner's electrical and electronic parts must not be reused for improper uses since they contain substances which constitute health hazards. E2 sign - indicates that ear defenders must be worn. 2 TECHNICAL INFORMATION (fig. 1) 2.1 Envisaged use This appliance has been designed for individual and professional use for the cleaning of vehicles, machines, boats, masonry, etc, to remove stubborn dirt using clean water and biodegradable chemical detergents. Vehicle engines may be washed only if the dirty water is disposed of as per regulations in force. - Intake water temperature: below 60 °C. - Intake water pressure: below 10 bar. - Operating ambient temperature: above 0 °C. The power-jet cleaner is compliant with the 98/37/EC Directive. 2.2 Operator Use of the cleaner requires specific technical skill and training and a good sense of responsibility. The operator must meet specific physical and mental requirements to be suitable for the job in hand; the clean er must therefore only be used by the appointed person. 2.3 Improper use Use by unskilled persons or those who have not read and understood the instructions in the manual is for bidden. The introduction of inflammable, explosive and toxic liquids into the cleaner is prohibited. Use of the cleaner in a potentially inflammable or explo sive atmosphere is forbidden. The use of non-original accessories and any other accessories not specifically intended for the model in question is prohibited. All modifications to the cleaner are prohibited. Any modifications made to the appliance shall render the Declaration of Conformity null and void and relieve the manufacturer of all liability under civil and criminal law. 2.4 Main components B1 - Engine B2 - Reduction gearbox (where fitted) B3 - Pump B4 - Gun with safety catch B5 - Lance B6 - High pressure hose B7 - Oil caps 2.4.1 Accessories C1 Nozzle cleaning tool C2 Rotopower (where fitted) 2.5 Technical data The technical data are specified in the enclosure. 2.6 Safety devices Caution - Danger! Never tamper with the safety devices. - Safety valve and pressure limiting valve The safety valve is also a pressure limiting valve. When the gun trigger is released, the valve opens and the water recirculates through the pump inlet. - Thermostat valve (D1) If the water temperature exceeds the temperature set by the manufacturer, the thermostat valve discharges the hot water and draws in an amount of cold water equal to the amount of water discharged. - Safety catch (D): prevents accidental spraying of water. 2.7 Noise levels At even short exposure times, noise may cause hearing impairment in the long term. Users must wear ear defenders to protect their hearing. 3 INSTALLATION (fig. 2) 3.1. Assembly Caution - Danger! All installation and assembly operations must be performed with the engine off. The assembly sequence is illustrated in fig. 2. 3.2 Fitting the pressure release caps To prevent oil leaks, the appliance is delivered with the oil intakes sealed with red caps which must be replaced with the pressure release caps supplied. 3.3 Assembling the rotating nozzle (where fitted) The rotating nozzle kit delivers greater washing power. 3.4 Water supply connection Caution - Danger! Only clean or filtered water should be used for intake. The delivery of the water intake tap should be equal to that of pump capacity. Do not use container and tanks to supply the appli ance. Place the cleaner as close to the water supply system as possible. 3.4.1 Connection points l Water outlet (OUTLET) n Water inlet with filter (INLET) 3.4.2 Connection to the mains water supply The cleaner can be connected directly to the mains drinking water supply only if the supply hose is fitted with a backflow preventer valve as per current regulations in force. Make sure that the hose is at least Ø 13 mm and that it is reinforced. 4 ADJUSTMENTS (fig. 3) 4.1 Adjusting the pressure The regulator (G) is used to adjust the working pressure. The pressure is shown on the pressure gauge. 4.2 Adjusting the nozzle Water flow is adjusted by regulating the nozzle (E). 5 INFORMATION FOR USE (fig. 4) Caution - Danger! Never use the cleaner when malfunctioning. In the event of damage, the high pressure hose must be replaced immediately to prevent bursts. 5.1 Preliminary checks Before using the cleaner, check the oil level: - in the engine (see engine constructor's manual); - in the reduction gearbox (where fitted); - in the pump. Check the reduction gearbox and pump oil gauges to check the oil level. It should be halfway up the gauge. If necessary, top up with oil having the same characteris tics (see the "Oil characteristics" table). 5.2 Controls For information about the engine controls, refer to the engine constructor's manual. - Water jet control lever (I). Caution - Danger! During operation the cleaner must be posi tioned on a flat surface firm enough to support it securely. 5.3 Starting the appliance Caution - Danger! Before starting up the cleaner check that the water supply hose is connected properly; use of the cleaner without water will damage the appliance. 1) Turn the water supply tap fully on. 2) Release the safety catch (D). English 11 3) Keep the gun trigger depressed and start the engine. 4) Keep the gun trigger depressed for a few seconds to vent the air from the pump. To prevent damage to the appliance, when running do not stop the water jet for more than 5 minutes at a time. 5.4 Stopping 1) Stop the engine. 2) Depress the gun trigger and discharge the residual pressure inside the hoses. 3) Engage the gun safety catch (D). 5.5 Refilling and using detergent IPlace the hose straight in the detergent container. 5.6 Recommended cleaning procedure Dissolve dirt by applying the detergent mixed with water to the surface while still dry. H S I When dealing with vertical surfaces work from the bot L tom upwards. G N Leave the detergent to act for 1-2 minutes but do not E allow the surface to dry. Starting from the bottom, use the high pressure jet at a minimum distance of 30 cm. Do not allow the rinse water to run onto unwashed surfaces. 5.7 Ending the working session 1) Stop the engine. 2) Turn off the water supply tap. 3) Discharge the residual pressure from the gun until all the water has come out of the nozzle. 4) Engage the gun safety catch (D). 5) Remove the water intake hose. 6) Remove the detergent hose from the container. 6 MAINTENANCE (fig. 5) Any maintenance operations not covered by this chap ter should be carried out by an Authorised Sales and Service Centre. Caution - Danger! Stop the engine before doing any work on the cleaner. 6.1 Cleaning the filter Clean the suction filter (L) after every 50 hours of operation. 6.2 Topping up the oil level The oil level must be topped up with the cleaner on a flat surface. Remove the casing (where fitted) to top up the oil level. Replace the casing (where fitted) when done. 6.2.1 Topping up the pump oil Add oil through the intake hole to restore the correct level. For oil characteristics, refer to the "Oil characteris tics" table. 6.2.2 Topping up the reduction gearbox oil (where fitted) Add oil through the intake hole to restore the correct level. For oil characteristics, refer to the "Oil characteris tics" table. 12 English 6.3 Oil Change Caution - Danger! Spent oil must not be dumped because it is a pollutant. It must be disposed of in accordance with legal requirements. Change pump and reduction gearbox oil (where fitted) after first 50 hours of operation, and every 500 hours thereafter. Remove the casing (where fitted) to change the oil. Replace the casing (where fitted) when done. 6.3.1 Changing the pump oil Unscrew the drain plug and allow all the spent oil to flow out. Screw the plug back into place. Pour in oil through the filler hole. Check that the oil level is correct. For oil characteristics, refer to the "Oil characteris tics" table. 6.3.2 Changing the reduction gearbox oil (where fitted) Unscrew the drain plug and allow all the spent oil to flow out. Screw the plug back into place. Pour in oil through the filler hole. Check that the oil level is correct. For oil characteristics, refer to the "Oil character istics" table. 7 TROUBLESHOOTING Table 1 - Oil characteristics Component Oil type Quantity (kg) Pump 850 SAE 30 W 0.9 Pump 840 SAE 30 W 0.9 Pump 830 SAE 30 W 0.3 Pump 820 SAE 30 W 0.3 Pump 810 SAE 75 W90 0.135 Reduction gearbox AGIP BLASIA W90 0.21 6.4 Storage Treat the appliance with non-corrosive, non-toxic anti freeze before storing it away for winter. Problem Possible causes Remedy Pump does not reach work ing pressure Nozzle worn Replace nozzle Water filter fouled Clean filter (fig.5) Water supply pressure low Turn on water supply tap fully Air being sucked into system Check tightness of hose fittings Air in pump Switch off the cleaner and keep depressing and releasing the gun trigger until the water comes out in a steady flow. Switch the cleaner back on again. Adjustable nozzle not positioned correctly Turn the adjustable nozzle "E" (+) (fig.3) Pressure drops during use Water intake from external tank Connect cleaner to the mains water supply Intake water too hot Reduce temperature Nozzle clogged Clean nozzle (fig.5) Water leakage Seals worn Have the seals replaced at your nearest Authorised Service Centre Cleaner noisy Water too hot Reduce temperature (see technical data Oil leakage Seals worn Contact your nearest Authorised Service Centre Engine malfunction Refer to the engine manufacturer's manual. Water escapes from ther mostat valve Water temperature inside nozzle has exceeded max. rated value stated on nameplate With appliance in operation, do not stop the water jet for more than 5 minutes at a time