Ameriphone MotionSensor AM-6000, homeappliance

Download!

system to work. components. present, change channel switch settings on all Notification System or other wireless signals is on after 60 seconds, replace with new battery. the system. If the red indicator light doesn't come sooner, by moving in front of the unit to activate Check the battery strength every six months, or 15' Area Monitored All settings must be identical for the new switch settings in the console. Remote Receiver, etc.) to match the If interference from another Alertmaster your neighborhood. battery as shown. 9V alkaline Install the 9V ➡ 15' of your other accessories (doorbell, 4.Change the switch settings on each on console. setting to exactly match new settings locate dip switch, change switch sons, it may be triggered by a system nearby in repeatedly activates by itself for no obvious rea If your system encounters interference and there is no adjustment necessary. setting. Under normal operating conditions, Battery and Operation Tests 6' monitored area may trigger activation. the unit. Caution: Small animals walking in the seconds to turn off the switch to avoid triggering outside the window. 3.Slide open battery door of AM-SX, position as shown. all individual switches to a new 2.Change the switch setting by sliding the AM-7000. AM-6000 console and the back of switch on the underside of the 1.Unplug AC cord and locate Dip preset in the factory to a standard channel Your system and all the accessories have been channel selection. same "channel." A "Dip switch" is used for to activate the base unit, it has to be on the all its accessories. For the Motion Sensor AM-SX nals to communicate between the base unit and The Alertmaster System uses special radio sig to the area being monitored, you will have 15 sent to the AM-6000 or AM-7000. Upon returning cator light will come on when a signal is being AM-6000 or the AM-7000 system. The red indi nal will be sent 15 seconds later to activate the monitored area will trigger the sensor and a sig the one minute set up period, any motion in the 60 second set up period to leave the area. After area. When you turn on the AM-SX you have a The AM-SX uses an infrared sensor to monitor the to avoid false triggering by some one walking Do not place the unit directly facing a window to a distance of 15 feet in front of the unit. tor an area approximately 15 feet in width, up at a height not to exceed six feet. It will moni the AM-SX on a wall, on a shelf or table edge, receivers. For optimal room coverage, install Alertmaster AM-6000 or AM-7000 and its Position the AM-SX within 80 feet from the CHANNEL SETTING OPERATIONS INSTALLATION ALERTMASTER Transmitter ) Cont. ( CHANNEL SETTING 1 2 3 4 ON Use a pen or pencil to set DIP switches to ON 4 3 2 1 match exactly as shown ON 1234 AM-6000 or AM-7000 9V Battery 4 3 2 1 ON Door AM-SX IN CASE OF DIFFICULTY If any problem should occur during operation of your Alertmaster Model AM-SX accessory, review list in your " Symptom and Remedy " the Alertmaster Model AM-6000 or AM-7000 Operating Instructions. Make sure no part of the Alertmaster Notification System is on or near metal surfaces or electronic equipment. Should the difficulty persist, contact Ameriphone or your authorized dealer for assistance. FCC INFORMATION The Alertmaster Model AM-SX uses an FCC approved transmitter, and complies with Part 15 of the FCC Rules. Its operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received, including interference that may cause undesired operation. WARRANTY LIMITED Ameriphone warrants the AM-SX against any defect in workmanship or material, for 1 a period of one year from the date of purchase. 0 0 1 If the product is defective and returned within 30 days of purchase, the unit will be - 0 replaced at the place of purchase at no charge. 2 2 5 If it is returned after 30 days but within one year, Ameriphone will repair or replace it at no charge. In repairing your AM-SX, we may use new or reconditioned parts. If 8 9 we elect to replace your AM-SX, we may replace it with a new or reconditioned 8 product of the same or similar design. Repair or replacement will be warranted for 7 0 either 90 days or the remaining time on the warranty period, whichever is longer. M When in need of warranty repair, please call our customer service department at 3 ∆ (800) 874-3005 (voice), (800) 772-2889 (TTY). They will help you process your 2 return shipment. You must prepay all shipping costs. 0 / 4 Implied warranties, including those of fitness for a particular purpose and mer chantability (unwritten warranty that the product is fit for ordinary use), are limited to ® one year from date of purchase. We will not pay for loss of time, inconvenience, loss E of use of your AM-SX or property damage caused by your AM-SX or its failure to N work, or any other incidental or consequential damages. Some states do not allow O H limitations on how long an implied warranty lasts or the exclusion of incidental or P I R consequential damages, so the above exclusions or imitations may not apply to you. E M We suggest you save the original package materials in the event that you need to A © ship your AM-SX back. When shipping for warranty repair, include your name, address, phone number, proof of date of purchase and a description of the problem. After repairing the product, we will ship it back to you at no cost within the United States. This warranty does not cover defects resulting from accidents, damage while in tran sit to our service location, alterations, unauthorized repair, failure to follow instruc tions, misuse, use outside the United States or Canada, fire, flood and acts of God. ® (AM-SX) Motion Sensor Works with ALERTMASTER Product Series ® OPERATING INSTRUCTIONS 12082 Western Avenue, Garden Grove, CA 92841 VOICE (800) 874-3005 TTY (800) 772-2889 FAX (714) 897-4703 ameriphonecs@plantronics.com www.ameriphone.com