American Water Heater Water Heater ITCE3-52/80/119, homeappliance

Download!

Residential Electric Lowboy 6-Year Limited Tank/Parts Warranty* All residential electric water heaters have the Fused Ceramic Shield lining, a tough, thick, durable coating of ceramic that is fused to the tank's interior surface at 1600˚F, forming a corrosion-resistant lining for years of dependable protection and use. • Dual Heating Elements Screw-in, direct immersion, 4500-watt, 240-volt heating elements for maximum effi ciency. • Non-CFC Foam Insulation The tank is surrounded by a thick coat of non-CFC polyurethane foam to trap heat inside the tank, saving energy. • Heat Traps Provided for inlet and outlet to reduce heat loss during standby. • Dip Tube Carries cold inlet water deep into the tank to minimize temperature dilution of hot water. • T&P Valve Conveniently located on the side of the tank to facilitate piping to a drain or external to the building. Also available with top T&P opening for fi eld installed top T&P valve. • 3/4" Water Connections Located on top. • Anode Rod Top-mounted, heavy-duty anode for added tank protection, extending the life of the tank. • Built-In Electric Junction Box Top-located, convenient junction box, ready for 1/2" or 3/4" conduit. • Thermostat/High Limit Control Combination control allows adjustment of water temperature while preventing overheat protection. • Code Approvals Listed to UL 174, 1987 NAECA current requirements, BOCA and ASHRAE 90.1-1999. All models are certifi ed at 300 PSI test pressure and 150 PSI working pressure. • Drain Valve Child-resistant, corrosion-resistant drain valve. *For complete warranty information consult the written warranty of American Water Heaters found at www.americanwaterheater.com, or call (800) 999-9515. Copyright© by American® Water Heaters 2008. All rights reserved. Copyright© by American® Water Heaters 2008. All rights reserved. NRESS00408 No part of this work may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or by any information storage retrieval system, without permission in writing from American Water Heaters. T&P VALVE ACCESS PANEL ACCESS PANEL DRAIN VALVE Residential Electric Lowboy ANODE JUNCTION BOX T&P VALVE HEIGHT TO HEIGHT TO GPH JACKET TOP OF SIDE T&P APPROX. GALLON RECOVERY DIAMETER HEATER VALVE SHIPPING MODEL NUMBER CAPACITY 90° RISE EF A B C WEIGHT 19 20.7 N/A 16 31-1/4 24-1/4 38 20.7 0.92 22 31-5/8 24-1/4 46.5 20.7 0.91 24 31-5/8 24-1/4 28 20.7 0.93 22 29-1/2 22-1/2 38 20.7 0.92 24 31-5/8 24-1/4 E61-19L-045DV 60 E61-40L-045DV*** 113 E61-50L-045DV*** 133 E62-30L-045DV 84 E62-40L-045DV 113 E62-50L-045DV 46.5 20.7 0.91 26 31-5/8 24-1/4 133 To order single element substitute "S" for "D" in model number. Delete "V" from model number for top T&P option, T&P opening on top of the heater with the valve shipped in the box for fi eld installation. All models include internal heat traps. Dimensions and specifi cations subject to change without notice in accordance with our policy of continuous product improvement. Dimensions on all charts shown in inches. All models are wired for non-simultaneous element operation. 3/4" water connection located on top. Top water connections are on 8" centers. ***Supplied with insulating jacket. Specifi cation Residential electric water heater(s) shall be Lowboy model ____________ as manufactured by American Water Heaters, or an approved equal, and shall have a ______ -year tank warranty and a ______ -year parts warranty, when installed in a residential application. Heater(s) shall have a storage capacity of ______ gallons and shall have a rated input of __________ KW at __________ Volts, single phase, 60 cycle AC, and shall be designed, tested and listed in accordance with Underwriter's Laboratories standard UL 174. Heaters shall meet or exceed the requirements of the Federal "National Appliance Energy Conservation Act of 1987" and shall comply with ASHRAE Standard 90.1-1999. The interior of the storage tank shall be lined with a Fused Ceramic Shield lining, fused to the tank at 1600°F, forming a corrosion-resistant lining; polymer linings are not acceptable. Each tank shall be furnished with an internal anode for cathodic protection. The unit must be equipped with a built-in electrical junction box. Electrical heating elements shall be screw-in, direct immersion, resistance type. Element operation shall be controlled by a thermostat for each element. A high temperature cut-off shall be supplied as an integral part of the heater. Element access panels shall be provided on the front of the heater for each element. A corrosion-resistant drain valve shall be provided on the front of each unit. The tank shall be totally encased in a metal jacket and insulated with a non-CFC foam to reduce standby heat loss. The tank must be design certifi ed for 300 PSI test pressure and 150 PSI working pressure. Distributed By: Order Entry and Sales 500 Princeton Road (FEDEX, UPS) Johnson City, TN 37601-2030 P.O. Box 4808 (Mailing) Johnson City, TN 37602-4808 (800) 937-1037 FAX (800) 581-7224 NRESS00408 Warranty and Service 500 Princeton Road (FEDEX, UPS) Johnson City, TN 37601-2030 P.O. Box 1597 (Mailing) Johnson City, TN 37605-1597 (800) 999-9515 FAX (800) 999-5210 No part of this work may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or by any information storage retrieval system, without permission in writing from American Water Heaters.