American Standard Colony Soft T975.500, homeappliance

Download!

Installation Instructions Instrucciones de Instalacion Instructions d'installation COLONY SOFT DECK MOUNT TRIM KIT JUEGO DECORATIVO PARA CUBIERTA COLONY T975.400/400BP TROUSSE DE GARNITURE POUR MONTAGE SUR PLAGE D'ÉVIER COLONY T975.500/500BP C Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-- please read these instructions carefully before you begin. Gracias por preferir American Standard…. El punto de referencia de la más fina calidad por más de 100 años. Para asegurar que su instalación se efectue de la mejor forma favor de leer estas instrucciones cuidadosamente antes de empezar. Nous vous remercions d'avoir choisi American Standard... synonyme de qualité supérieure depuis plus de 100 ans. Pour s'assurer d'une installation sans inconvénients, veuillez lire attentivement ces instructions avant de commencer. H Certified to comply with ANSI A112.18.1 U.S. Patent No. D403,750 M968757D 1 SPOUT INSTALLATION CAUTION Turn off hot and cold water supplies before beginning. 4 3 5 1 Complete FINISHED DECK (A) before trim installation. 2 Turn off the water supplies. REMOVE ALL A Remove the GUARDS (1) from the VALVE BODIES (2). Remove the SPOUT GUARD (3) and 1/4" PLUG (4) from the SPOUT SHANK (5). The SPOUT SHANK (6) height should be 1" to 2" above the FINISHED DECK (A). Cut the SPOUT SHANK (5) if necessary. Remove all burrs and bevel the end of the shank. Failure to do so may damage the SPOUT O-ring during installation and cause water leakage. Drill a 3/16" HOLE (C) in the finished deck. See TEMPLATE for location. Lubricate the SPOUT O-RING (6). Remove the PLUG BUTTON (7) from the SPOUT (8). BURRS AND BEVEL 1"- 2" Position the RUBBER RING (9) in the GROOVE (B) in the base of the SPOUT (8). Push the SPOUT (8) down onto the SPOUT SHANK (5) and align the SPOUT PIN (12) with the 3/16" DRILLED HOLE (C) in the FINISHED DECK (A). Tighten the SET SCREW (10) securely with the 5mm HEX KEY (11). Insert the PLUG BUTTON (7) into the SPOUT (8). ARMADO DE LA LLAVE ADVERTENCIA: Cierre la tuberia de la ali mentación del agua caliente y fría antes de comenzar lainstalación 20.5mm (13/16") Complete la CUBIERTA TERMINADA (A) antes de instalar el juego decorativo. Cierre el suministro de agua. Quite los PROTECTORES (1) del CUERPO DE LAS VÁLVULAS (2). Quite el PROTECTOR DEL GRIFO (3) y el TAPÓN (4) de 1/4 de pulgada (6,4 mm) del POSTE DEL GRIFO (5). La altura del POSTE DEL GRIFO (5) debe ser de 1 a 2 pulgadas (25 a 51 mm) sobre la CUBIERTA TERMINADA (A). Corte el POSTE DEL GRIFO (5) si es necesario. Quite todas las rebabas y bisele el extremo del poste. Si no lo hace, puede dañar la junta tórica del GRIFO durante la instalación y ocasionar fugas. Taladre un AGUJERO (C) de 3/16 de pulgada (4,8 mm) en la cubierta terminada. Consulte la PLANTILLA para conocer la ubicación. Lubrique las JUNTAS TÓRICAS DEL GRIFO (6). Quite el BOTÓN OBTURADOR (7) del GRIFO (8). Coloque el ANILLO DE CAUCHO (9) en la RANURA (B) de la base del GRIFO (8). Empuje el GRIFO (8) hacia abajo sobre el POSTE DEL GRIFO (5) y alinee el PASADOR DEL FRONT 3/16" DIA. HOLE TEMPLATE FOR SPOUT ROLL PIN LOCATION PLANTILLA DE UBICACIÓN DEL PASADOR DE GIRO DEL GRIFO GUIDE POUR L'EMPLACEMENT DE LA GOUPILLE CYLINDRIQUE DU BEC. C GRIFO (12) con el AGUJERO PERFORADO (C) de 3/16 de pulgada (4,8 mm) en la CUBIERTA TERMINADA (A). Apriete firmemente el TORNILLO DE SUJECIÓN (10) utilizando la LLAVE HEXAGONAL (11) de 5 mm. Inserte el BOTÓN OBTURADOR (7) en el GRIFO (8). 5 INSTALLER LE ROBINET ATTENTION Fermer l'alimentation d'eau chaude et froideavant de commencer. Terminer la PLAGE DE L'ÉVIER FINIE (A) avant d'installer les garnitures. Couper l'alimentation d'eau. A Retirer les PROTECTEURS (1) des CORPS DE VANNE (2). Retirer le PROTECTEUR DU BEC (3) et le TAMPON (4) de 6 mm de la TIGE DU BEC (5). La TIGE DU BEC (6) devrait dépasser la PLAGE DE L'ÉVIER FINIE (A) d'une hauteur de 2,5 à 5,0 cm. Couper la TIGE DU BEC (5) si nécessaire. Retirer toutes les barbures et niveler l'extrémité de la tige. Sinon, le joint torique du BEC risque d'être endommagé durant l'installation et causer des fuites d'eau. Percer un TROU (C) de 5 mm dans la plage de l'évier finie. Se 5 reporter au GUIDE pour connaître l'emplacement. Lubrifier le JOINT TORIQUE DU BEC (6) et C Retirer la CAPSULE DU TAMPON (7) du BEC (8). 8 11 10 12 7 B Placer la BAGUE DE CAOUTCHOUC (9) dans la RAINURE (8) située dans la base du BEC (8). Pousser le BEC (8) vers le bas dans la TIGE DU BEC (5) et aligner la GOUPILLE DU BEC (12) avec le TROU PERCÉ (C) de 5 mm situé dans la PLAGE DE L'ÉVIER FINIE (A). 6 Serrer la VIS DE RÉGLAGE (10) fermement au moyen d'une CLÉ HEXAGONALE (11) de 5 mm. 12 9 Insérer la CAPSULE DU TAMPON (7) dans le BEC (8). 2 VALVE TRIM Fit ESCUTCHEON SEALS (1) into underside of VALVE ESCUTCHEONS (2). Thread the VALVE ESCUTCHEONS (2) into the VALVE BODIES (3). Align the HANDLE STEM (4) with the SLEEVE (5) as necessary. Thread the VALVE ESCUTCHEON (2) into the BODIES (3) until the ESCUTCHEON (2) contacts the finished deck. JUEGO DE ESCUDETE Coloque los SELLOS DE LOS CHAPETONES (1) en la parte inferior de los CHAPETONES DE LAS VÁLVULAS (2). Enrosque los CHAPETONES DE LAS VÁLVULAS (2) en los CUERPOS DE LAS VÁLVULAS (3). Alinee el TALLO DE LA LLAVE (4) con el MANGUITO (5) si es necesario. Enrosque el 2 3 5 4 1 CHAPETÓN DE LA VÁLVULA (2) en el CUERPO (3) hasta que el CHAPETÓN (2) haga contacto con la cubierta terminada. KIT D'ÉCUSSON Insérer les JOINTS DE ROSACE (1) dans la face inférieure des JOINTS DE VANNE (2). Enfiler les JOINTS DE VANNE (2) dans les CORPS DE VANNE (3). Aligner la TIGE DE LA POIGNÉE (4) avec le MANCHON (5), au besoin. Enfiler le JOINT DE VANNE (2) dans les CORPS (3) jusqu'à ce que le JOINT (2) entre en contact avec la plage de l'évier finie. 3 INSTALL LEVER HANDLE TRIM Turn HANDLE STEM (1) to "OFF" position. 4 Place the HANDLE ADAPTER (2) on the HANDLE STEM (1). Install the ADAPTER SCREW (3) and tighten securely. 5 Position LEVER HANDLE (4) and place on ADAPTER (2). Install the HANDLE SCREW (5) and tighten securely. INSTALACIÓN DE LA MANIJA 3 Gire el TALLO DE LA LLAVE (1) a la posición de cierre. 2 Coloque el ADAPTADOR DE LA LLAVE (2) en el TALLO DE LA LLAVE (1). Instale el TORNILLO DEL ADAPTADOR (3) y apriételo firmemente. Ajuste la posición de la LLAVE DE PALANCA (4) y colóquela sobre el ADAPTADOR (2). 1 Coloque el TORNILLO DE LA LLAVE (5) y apriételo firmemente. INSTALLATION DE LA POIGNÉE Placer la TIGE DE LA POIGNÉE (1) en position « FERMÉE ». Placer l'ADAPTATEUR DE POIGNÉE (2) sur la TIGE DE LA POIGNÉE (1). Installer la VIS D'ADAPTATION (3) et serrer fermement. Mettre la MANETTE À VOLANT (4) en position et la placer sur l'ADAPTATEUR (2). Installer la VIS POUR MANETTE (5) et serrer fermement. 4 INSTALL ACRYLIC HANDLE TRIM Turn HANDLE STEM (1) to "OFF" position. Place the HANDLE ADAPTER (2) on the HANDLE STEM (1). Position ACRYLIC HANDLE (3) and install on ADAPTER (2). Install the HANDLE SCREW (4) and tighten securely. Push in INDEX BUTTON (5). (Hot-left side , Cold-Right side) INSTALE LAS MANIJAS ACRÍLICAS Gire el TALLO DE LA LLAVE (1) a la posición de cierre Coloque el ADAPTADOR DE PIE DE LA MANIJA (2) en el PIE DE LA MANIJA (1). Ubique la MANIJA ACRÍLICA (3) en el ADAPTADOR DE PIE DE LA MANIJA (2). Instale el TORNILLO DE MANIJA (4) y ajuste bien. Presione sobre BOTÓN ÍNDICE (5). INSTALLER LES POIGNÉES EN ACRYLIQUE Placer la TIGE DE LA POIGNÉE (1) en position « FERMÉE ». Placer l'ADAPTATEUR DE POIGNÉE (2) sur la TIGE DE LA POIGNÉE (1). Placer la POIGNÉE EN ACRYLIQUE (3) sur la l'ADAPTATEUR DE POIGNÉE (2). Installer les VIS POUR LES POIGNÉES (4) et bien serrer. Insérer le BOUTON INDICATEUR (5). 5 H 4 3 2 1 M968757D 5 TEST INSTALLED FAUCET Remove STREAM STRAIGHTENER (1). With handles in OFF position, turn on water supplies and check all connections for leaks. Operate both handles to flush water lines thoroughly. Replace STREAM STRAIGHTENER (1). 2 PRUEBA DE LA LLAVE INSTALADA Quite el REGULADOR DEL CHORRO DE AGUA (1). Cierre las llaves, abra el suministro de agua y revise las conexiones para asegurar que no tengan fugas. Girar ambos manerales para dejar fluir el agua de las tuberias. 1 Accionar la varilla del drenaje y cheque contra fugas. Reinstalar el REGULADOR DEL CHORRO DE AGUA (1). TESTER L'INSTALLATION DU ROBINET Retirer le DISPOSITIF DE REDRESSEMENT DU JET (1). Tout en gardant les poignées en position FERMÉE, mettre l'alimentation d'eau en marche et vérifier tous les raccords pour s'assurer qu'il n'y ait pas de fuites. Ouvrir les deux POIGNÉES, rincer les conduits d'eau abondamment. Opérer la TIGE DE LEVAGE et vérifier si le VIDAGE fuit. Replacer le DISPOSITIF DE REDRESSEMENT DU JET (1). 6 If faucet drips proceed as follows: Si le robinet coule, suivre les instructions suivantes: Si la llave gotea proceda como sigue: Stream straightener may accumulate dirt causing distorted and reduced water flow. Remove aerator and rinse clean. If spout drips, operate handles several times from OFF to ON position. Do not force-handles turn only 90˚. CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. El aireador tal vez acumule suciedad, causando un flujo no uniforme del agua Remover el aireador, enjuagar y limpiar. Si la salida gotea gire los manerales varias veces desde la posición de cer rado a la posición de abierto. No force los manerales, solamente girelos a 90 grados. INSTRUCCIONES DE CUIDADO DEL PRODUCTO: LIMPIE EL PRODUCTO CON AGUA LIMPIA Y SÉQUELO CON UNA TELA SUAVE DE FRANELA DE ALGODÓN. NO LIMPIE EL PRODUCTO CON JABÓN, ÁCIDOS, PULIDORES, ABRASIVOS, LIMPIADORES FUERTES O TELAS ÁSPERAS. La saleté peut s'accumuler dans l'aérateur et causer un débit d'eau plus faible ou inégal. Enlever l'aérateur et rincer. Si le bec coule, ouvrir et fermer les poignées plusieurs fois de suite. Ne pas forcer. Tourner seulement à 90˚. INSTRUCTIONS POUR L'ENTRETIEN FAIRE : SIMPLEMENT RINCER LE PRODUIT AVEC DE L'EAU CLAIRE JUSQU'À CE QU'IL SOIT PROPRE SÉCHER AVEC UN LINGE DE FLANELLE DE COTON DOUX. NE PAS FAIRE : NE PAS NETTOYER LE PRODUIT AVEC DES SAVONS, DE L'ACIDE, DU POLISH, DES ABRASIFS, DES NETTOYANTS AGRESSIFS OU UN LINGE À TEXTURE RUGUEUSE. HOTLINE FOR HELP NUMBERO DE EMERGENCIA ASSISTANCE TÉLÉPHONIQUE For toll-free information and answers to your questions, call: Para información y respuestas a sus preguntas, llame sin costo al: Pour information et réponses à vos questions, composer sans frais: 1 800 442-1902 Weekdays Días laborales de las Sur semaine: 8:00 to 8:00 p.m. EST CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays Días laborales de las Sur semaine: 8:00 to 7:00 p.m. EST Product names listed herein are trademarks of American Standard Inc. ©American Standard Inc. 2001 M968757D COLONY SOFT DECK MOUNT TRIM KIT JUEGO DECORATIVO PARA CUBIERTA COLONY TROUSSE DE GARNITURE POUR MONTAGE SUR PLAGE D'ÉVIER COLONY MODEL NUMBER NÚMERO DE MODELO H M918504-0070A SCREW Tornillo VIS M908423-0070A ACRYLIC HANDLE Maneral Acrilico POIGNÉE ACRYLIQUE M918075-0070A HANDLE SCREW TORNILLO DE LA MANIJA VIS DE LA POIGNÉE M918504-0070A SCREW TORNILLO VIS M918021-0070A ADAPTER ADAPTAR APPROPRIER M961460-0020A VALVE ESCUTCHEON KIT JUEGO DE ESCUDETE KIT D'ÉCUSSON M950144-0070A INDEX, BUTTON, HOT Boton Indicador de Agua Caliente BOUTON INDEX, CHAUD M950143-0070A INDEX, BUTTON, COLD Boton Indicador de Agua Fria BOUTON INDEX, FROID M916803-YYY0A METAL LEVER HANDLE MANIJA METÁLICA POIGNÉE MÉTALLIQUE PLEINE M961461-YYY0A BUTTON AND SCREW BOTON Y TORNILLO BOUTON ET VIS NUMÉRO DE MODÈLE T975.400BP T975.400 T975.500BP T975.500 M961640-YYY0A SPOUT BOQUILLA BEC 028678-0070A STREAM STRAIGHTENER REGULADOR DE CHORRO DE AGUA REDRESSEUR DE JET Replace the "YYY" with appropriate finish code Reemplace las letras "YYY" por el código de acabado Remplacer le "YYY" par le code de finition approprié CHROME, CROMO, CHROME POLISHED BRASS, BRONCE PULIDO, LAITON POLI 002 099 M968757D Installation Instructions DECK MOUNT T990 SERIES TUB FILLERS COLONY DIVERTER & PERSONAL SHOWER TRIM KIT Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1 U.S. Patent No. D403,750 M968356 INDEX BUTTON HANDLE SCREW HANDLE VALVE ESCUTCHEON 1 INSTALL DIVERTER VALVE TRIM REMOVE THE DIVERTER GUARD. SEAL WASHER HAND SHOWER SEAL WASHER HOLDER SHOWER ESCUTCHEON RUBBER RING SHOWER HOSE DIVERTER GUARD Place the ESCUTCHEON SEAL over the DIVERTER BODY. Thread the VALVE ESCUTCHEON into the DIVERTER BODY. Align the HANDLE STEM with the SLEEVE as necessary. Thread the VALVE ESCUTCHEON into the BODY until the ESCUTCHEON contacts the finished deck. HANDLE STEM ESCUTCHEON SEAL SLEEVE VALVE ESCUTCHEON FINISHED DECK 2 INSTALL HANDLE TRIM Turn HANDLE STEM fully clockwise (Tub Filler position). Place the HANDLE on the HANDLE STEM. Install the HANDLE SCREW and tighten securely. INDEX BUTTON HANDLE HANDLE SCREW Push the INDEX BUTTON into the top of HANDLE. HANDLE STEM 3 INSTALL HAND SHOWER Unscrew the HOLDER from the SHOWER ESCUTCHEON. Slip the SHOWER HOSE through the HOLDER and the SHOWER ESCUTCHEON. Insert a SEAL WASHER into the SHOWER HOSE CONNECTOR. Pull out the SLEEVE GUARD and HOSE. Unthread the SLEEVE GUARD from the HOSE END connection. Be careful not to allow the HOSE to fall back through the SLEEVE. Thread the SHOWER HOSE onto the HOSE END connection and tighten securely. SHOWER HOSE SLEEVE HAND SHOWER SEAL WASHER SHOWER HOSE HOLDER SHOWER ESCUTCHEON RUBBER RING GUARD Apply a sealant around the HOSE HOLE. SEAL WASHER HOSE END HOSE SLEEVE HAND SHOWER SEAL WASHER Thread the SHOWER ESCUTCHEON into the SLEEVE until the ESCUTCHEON contacts the finished deck. Loosen the SET SCREW in the SHOWER ESCUTCHEON and rotate the ESCUTCHEON towards the center of the tub. Retighten the SET SCREW. Thread the HOLDER into the SHOWER ESCUTCHEON. Insert a SEAL WASHER into the SHOWER HOSE connector and connect the HAND SHOWER. Place the HAND SHOWER into the HOLDER. HOTLINE FOR HELP For toll-free information and answers to your questions, call: 1 (800) 442-1902 Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) HOLDER SLEEVE SET SCREW SHOWER ESCUTCHEON SEALANT M968356 Product names listed herein are trademarks of American Standard Inc. ©American Standard Inc. 2000 DECK MOUNT TUB SYSTEMS ROUGH VALVE KIT Installation Instructions R800 SERIES R810 SERIES R810 SERIES Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please R800 SERIES read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1 1 ROUGHING-IN U.S. Patent No. D403,750 1. DECK THICKNESS M968650C 2 1 D MAX. ACRYLIC BATH MOUNTING 1 FINISHED DECK 1-3/8 D MAX. TOTAL DECK THICKNESS UP TO 2-1/2" 4 2. FINISHED DECK FINISHED DECK VARIABILITY ACCOMMODATES DECKING MATERIAL (TILE, MARBLE, CORIAN®...) TO 1" THICK 3. FITTING MOUNTING SURFACE ADJUSTABILITY, TO 1-1/2" THICK 1" D (2) 1-3/8 D HOLES 3 (2) 1-3/8 D 7-1/8 HOLES 4. ACRYLIC BATHS ADJUSTABILITY, TO 1-1/2" THICK 1" D FITTING MOUNTING SURFACE 2 MOUNT SPOUT SHANK 1/2" COPPER INLET SUPPLIES 8" to 12" 10" for R810 8" to 12" 10" for R810 DECK MOUNTING HOLES Drill holes in mounting deck as shown. The maximum allowable deck thickness is 1-1/2". Insert the SPOUT SHANK through the mounting deck from below. Assemble the SPOUT SHANK LOCK RING so it is flush with the top of the threads on the SHANK. SPOUT SHANK LOCK RING SPOUT SHANK LOCK RING FLUSH WITH TOP OF THREADS ON SPOUT SHANK 1-1/2 MAX. SPOUT SHANK FITTING MOUNTING DECK FRICTION WASHER MOUNTING NUT SPOUT SHANK 3 MOUNT VALVE BODIES Cut the copper outlet tubes of the VALVE BODIES as required. (Not necessary for R810). Insert the HOT and COLD VALVE BODIES into the TEE. (Not necessary for R810). The HOT VALVE BODY is marked with a red label. Insert the VALVE BODIES and TEE through the mounting deck from below. Assemble the VALVE LOCK RINGS so they are flush with the top of the VALVE BODIES. Insert the SPOUT SHANK into the TEE. (Not necessary for R810). VALVE BODY FITTING MOUNTING DECK VALVE VALVE LOCK RING FLUSH WITH TOP OF THREADS ON VALVE SHANK VALVE LOCK RING # 8 SCREWS SPOUT LOCK RING SHANK Tighten the VALVE BODY and SHANK MOUNTING NUTS securely. Fasten the VALVE LOCK RING to the wooden mounting surface with #8 screws (not provided). 4 SOLDER CONNECTIONS FRICTION WASHER COLD MOUNTING NUT HOT TEE OUTLET TUBE (CUT AS REQUIRED) SPOUT GUARD 1/4" PLUG Connect the water supply lines to the copper inlet tubes of the VALVE BODY. Solder all TEE and WATER SUPPLY CONNECTIONS. Remove the GUARD from the SPOUT SHANK. Assemble the 1/4" PLUG to the SPOUT SHANK with a thread sealant. Turn on the water supplies and check all connections for leakage. Replace the GUARD on the SPOUT SHANK. Turn off the water supplies. 5 SERVICE TEE CONNECTIONS WATER SUPPLY CONNECTIONS TO CHANGE THE DIRECTION OF HANDLE ROTATION DEEP SOCKET 17mm (11/16") Turn off the water supplies. Turn HANDLE to the off position. Unscrew the VALVE LOCK NUT and remove. A 17mm deep socket is required. Remove the CARTRIDGE by pulling upon the SLEEVE. Remove the SLEEVE from the CARTRIDGE. Remove the SPRING CLIP. Remove the STOP WASHER. Turn it 90˚ and replace. 90 STOP WASHER VALVE VALVE LOCK NUT SCREW SLEEVE SPRING CLIP Replace the SPRING CLIP. Reverse the above steps to reassembly the components. If the spout drips, operate the handles several times from the off to the on position. Do not force - the handles only turn 90˚ CARTRIDGE M968650C VALVE LOCK RING M906671-0070A VALVE LOCK NUT A911546-0070A DECK MOUNT TUB SYSTEMS MODEL NUMBERS R800 R810 SPINDLE 903898-0070A VALVE CARTRIDGE 994053-0070A VALVE MOUNTING KIT M962278-0070A SCREW 918319-0070A SPOUT LOCK RING A906110-0070A SPOUT MOUNTING KIT M962279-0070A DEEP SOCKET 17mm (11/16") M962273-0070A SOCKET NOT INCLUDED WITH FITTING HOTLINE FOR HELP For toll-free information and answers to your questions, call: 1 (800) 442-1902 Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Product names listed herein are trademarks of American Standard Inc. C American Standard Inc. 2003 R810 SERIES *WITH BRAZED TEE M968650C DECK MOUNT TUB FILLERS Installation Instructions R890 SERIES DIVERTER & PERSONAL SHOWER ROUGH VALVE KIT Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1 1 ROUGHING-IN 6 to 18 FINISHED ACRYLIC U.S. Patent No. D403,750 4 1. DECK THICKNESS M968355D BATH MOUNTING 1 1-3/8 D HOLE DECK 1-3/8 D MAX. 2 1-3/8 D MAX. TOTAL DECK THICKNESS UP TO 2-1/2" 2. FINISHED DECK FINISHED DECK VARIABILITY ACCOMMODATES DECKING MATERIAL (TILE, MARBLE, CORIAN®...) TO 1" THICK 3. FITTING MOUNTING SURFACE ADJUSTABILITY, TO 1-1/2" THICK 3-5/8 4-5/16 3 5-5/16 B U T 1/2" NPT 1-3/8 D 4. ACRYLIC BATHS ADJUSTABILITY, TO 1-1/2" THICK 1-3/8 D HOLE 1-3/8 D HOLE FITTING MOUNTING SURFACE SHW 1/2" NPT INLET FOR DIVERTER 6 to 18 DECK MOUNTING HOLES FOR HAND SHOWER 2 LOCATION OF R890 WHEN USED WITH R800R800 ROUGH VALVE KIT R890 SERIES DIVERTER & PERSONAL SHOWER ROUGH VALVE KIT 8" to 12" A A 6" to 18" "A" DIMENSION CAN BE FLEXIBLE TO HAND SHOWER CONNECTION HOT AND COLD VALVE BODIES ACCOMMODATE CUSTOMER'S REQUIREMENTS BATH SPOUT CONNECTION DIVERTER VALVE B U T SHW 1/2" COPPER WATER TUBE INLET (MIXED SUPPLY FROM BATH 1/2" COPPER WATER TUBE (MIXED SUPPLY TO TUB FILLER SPOUT) FITTING) HOSE OUTLET (MIXED SUPPLY HOT INLET COLD INLET PLUMBER TO MAKE ALL PIPING CONNECTIONS BETWEEN VALVE BODIES, SUPPLY TO TRANSFER VALVE AND CONNECTION TO BATH SPOUT. PIPING SHOWN SHADED IS NOT SUPPLIED AND MUST BE FURNISHED BY INSTALLER. TO HAND SHOWER) 3 NOTE: Use thread sealant on all threaded connections. INSTALLATION 1 1-3/8" Dia. HOLE FOR HAND Drop the SLEEVE (1) into the hole in the mounting deck. SHOWER 9 Assemble the WASHER (2) and LOCKNUT (3) to the SLEEVE (1) and tighten securely. For copper water tube installations, make two 4" long adapter nipples ( 1/2" Male NPT x 1/2" CWT ). Thread nipples into the inlet and tub outlet of the DIVERTER BODY. Tighten connections securely. Do Not Solder these Connections on the DIVERTER BODY. Damage may occur. #8 SCREWS FITTING MOUNTING SURFACE 2 3 Thread HOSE (4) into the SHOWER CONNECTION (5) of the DIVERTER BODY (6) 8 and tighten securely. Check with local plumbing codes for backflow prevention requirements. Install a backflow prevention device if required. 7 Assemble MOUNTING NUT (7) and WASHER (8) onto DIVERTER BODY (6). 6 Insert the DIVERTER BODY (6) through the mounting deck from below. Assemble the VALVE LOCK RING (9) so it is flush with the top of the DIVERTER BODY (6). Position the DIVERTER BODY (6) as required and tighten the MOUNTING NUT (7) securely. Fasten the VALVE LOCK RING (9) to the wooden VALVE LOCK RING FLUSH WITH TOP OF THREADS ON VALVE SHANK 5 WATER INLET 4" LONG ADAPTER NIPPLES mounting surface with #8 screws (not provided). Connect the water inlet and tub outlet lines to the DIVERTER BODY (6). #8 SCREWS TUB OUTLET VALVE BODY 4 TEST Note: Test Cap not provided. SLEEVE Cap the HOSE OUTLET. Remove the DIVERTER GUARD. Remove the SPOUT GUARD. Assemble the 1/4" PLUG to the SPOUT SHANK with a thread sealant. See the R800 SERIES ROUGH VALVE KIT instructions for details. DIVERTER GUARD GUARD SLEEVE Turn on the water supplies. Rotate the DIVERTER SLEEVE back and forth fully. Check all connections for leakage. Turn off the water supplies. Replace the DIVERTER GUARD and the SPOUT GUARD. Remove the CAP from the HOSE OUTLET. 5 HOSE DIVERTER SLEEVE 1/2" COPPER WATER TUBE (MIXED SUPPLY TO TUB FILLER SPOUT) HOSE OUTLET (MIXED SUPPLY 1/2" COPPER WATER TUBE INLET (MIXED SUPPLY FROM BATH FITTING) CAP HOSE END Insert the HOSE through the SLEEVE from below the mounting deck. Thread the SLEEVE GUARD onto the HOSE END connection. Insert the SLEEVE GUARD into the SLEEVE. 6 SERVICE TO REMOVE DIVERTER Turn off the water supplies. Turn HANDLE to the off position. Remove the SLEEVE from DIVERTER by losening screw. Using 14mm (9/16") Deep Socket, remove diverter. SCREW DIVERTER SLEEVE DIVERTER HOSE DEEP SOCKET 14mm (9/16") M968355D SCREW 918319-0070A DIVERTER SLEEVE 903898-0070A DIVERTER 954559-0070A DIVERTER & PERSONAL SHOWER ROUGH VALVE KIT MODEL NUMBER R890 VALVE LOCK RING M906671-0070A VALVE MOUNTING KIT M962278-0070A SLEEVE 922700-0070A SLEEVE MOUNTING KIT M962280-0070A HOSE M923016-0070 HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1-800 442-1902 Weekdays 8:00 a.m. to 8:00 p.m. EST IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST IN MEXICO 01-800-839-12-00 Product names listed herein are trademarks of American Standard Inc. © American Standard Inc. 2004 M968355D