American Standard BERWICK T430.50X, homeappliance

Download!

T M PRESSURE BALANCED BATH AND SHOWER FITTINGS Installation Instructions 1480.500 1480SS.500 T480.500 Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-- please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1 U.S. Patent No. D400,652 M968395 Rev. 1.1 ROUGHING-IN DIMENSIONS To assure proper positioning in relation to wall, note roughing-in dimensions. 1-5/8" TO SHOWER FLANGE 4" REF. FINISHED WALL 5-1/2" REF. "SEE ILLUSTRATION 3-1/4" 1/2" I.P.S. OPTIONAL TO FINISHED FLOOR USUALLY BETWEEN 65'' AND 78'' VALVE BODY WITH STOPS SHOWER ARM BELOW" 74" FOR HEAD CLEARANCE 18" OPTIONAL TOP OF TUB RIM SHR. 1/2" NOM. COPPER SWEAT SWEAT 1" MIN. 5-1/8" REF. BOTTOM OF TUB INLETS 4-1/16" 7-5/8" BATH 1/2" NPT 4" 1/2" COPPER OR1/2" NPT INLETS 1/2" NOM. COPPER SWEAT 1/2" SWEAT PLUG VALVE BODY 1/2" NPT PLUG PRESSURE BALANCING UNIT ADAPTOR AND MTG. SCREWS CARTRIDGE CARTRIDGE SEALS HOT LIMIT STOP ESCUTCHEON SCREWS CAP HANDLE BUSHING INLETS TUB 1/2" NOM. COPPER SWEAT 2" 4-1/16" CARTRIDGE SCREW SET THREADED INLETS SWEAT 3-3/8" INLETS 3-3/8" SHR. 1/2" NPT INLETS 1/2" NPT TUB PORT 1/2" NPT THREADED INLETS (STOPS) DIVERTER SPOUT ESCUTCHEON SCREW METAL LEVER HANDLE INLETS (STOPS) INLETS 1/2" NOM. COPPER SWEAT TUB 1/2" NOM. COPPER SWEAT 5-7/8" SHR. 1/2" NOM. COPPER SWEAT 4-1/16" SHR. 5-7/8" 1/2" NPT 3-3/8" TUB PORT 1/2" NPT' INLETS 1/2" NPT HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1-800-442-1902 Weekdays 8:00 a.m. to 6:00 p.m. EST IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST IN MEXICO 01-800-839-12-00 Product names listed herein are trademarks of American Standard Inc. © AS America, Inc. 2008 1 Turn off water at MAIN supply. To prevent damage temporarily remove STOPS when water supply lines are soldered to the manifold. CAUTION NOTE When soldering, remove PLASTER GUARD, CARTRIDGES and CHECK STOPS (IF PRESENT). When finished soldering, flush valve body, replace cartridges, check stops (if present) and plaster guard FLANGE SHOWER HEAD to continue installation. Use thread sealant or Teflon tape on threaded connections ROUGHING-IN See Roughing-in diagram on reverse side. Connect RISER PIPE to MANIFOLD top outlet marked "SHR". Connect TUB FILLER PIPE at bottom outlet marked "TUB". Supply connections are: 1/2" copper sweat for sweat inlets. 1/2" female NPT for threaded inlets. For proper positioning the finished wall must be within side wall of PLASTER GUARD. BRACE (4) * RISER PIPE * BODY HOT PLUG (NPT) SHOWER ARM COLD STEM CARTRIDGE SCREWS If the valve is installed on a fiberglass or other thin wall application, the PLASTER GUARD can be used as a support: Cut a 3" dia. hole in the shower stall. PLUG (SWEAT) PLASTER GUARD If stops are used drill two additional 1" holes to allow access to the stops. Remove PLASTER GUARD, rotate 180˚ so that indicated screw holes fit manifold. Push CAP on valve, place ESCUTCHEON and attach with screws. Connect hot and cold water supplies. For support, use pipe BRACES secured to wooden braces. With valve turned off, turn on water supplies and check for leaks. 2 INSTALL TRIM When finished, tiling the wall, remove PLASTER GUARD. Push on CAP. Mount ESCUTCHEON with SCREWS. Install HANDLE by pushing it onto CARTRIDGE STEM and tightening SET SCREW from below. Install SHOWER ARM with FLANGE and SHOWER HEAD. Install SPOUT. Check proper operation of HANDLE and DIVERTER SPOUT. TUB FILLER TUBES* (5/8" O.D. - 1/2" NOMINAL) REMOVE BURRS FROM TUBE * NOT INCLUDED IN KIT CARTRIDGE STEM ESCUTCHEON SCREWS ESCUTCHEON CAP SPOUT HANDLE BUSHING METAL LEVER HANDLE SET SCREW 3 HOT LIMIT STOP 4 SERVICE By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP reduces risk of accidental scalding. To set the maximum hot water temperature of your SEVA faucets, all you need to do adjust the setting on the HOT LIMIT SAFETY STOP. Remove HANDLE, CAP and HOT LIMIT STOP. Follow "A" or "B" to adjust maximum discharge temperature. "A" "B" PRY FORWARD TO UNLOCK AND ROTATE COUNTER CLOCKWISE ONE CLICKPRY FORWARD TO UNLOCK AND ROTATE CLOCKWISE If faucet drips, operate handle several times from "off" to "on". Do not apply excessive force. Clogged CARTRIDGE inlets may cause reduced flow in "full on" hot or cold. To clean inlets, first turn off water supply, then: Remove HANDLE, CAP, HOT LIMIT STOP and CARTRIDGE. Clean inlets and MANIFOLD. Reassemble CARTRIDGE, alternately tightening screws. Replace HOT LIMIT STOP , CAP and HANDLE. Check flow. ADJUSTMENT WHEN WATER IS TOO HOT ADJUSTMENT WHEN WATER IS TOO COLD VALVE BODY MANIFOLD CARTRIDGE SEALS CARTRIDGE CARTRIDGE MTG. SCREWS HOT LIMIT STOP M968395 Rev. 1.1